搜索资源列表
source
- 在电机控制中，从交流变直流的BOOST电流的控制程序-In motor control, from the exchange of variable DC current of the control procedures BOOST
DC_transmission_system_with_the_power_flow_calcula
- 该程序是一个含直流输电系统的潮流计算程序 程序运行需要包含Boost库文件,需要在VS2005环境以上(VC6.0不完全符合C++标准,可能有些变量作用域问题,无法通过调试) 潮流程序计算主要参考<<现代电力系统分析>>王锡凡主编2003-The program is a direct current transmission system with power flow calculation program run Boost library files ne
swra305
- CC1110和CC2510的LED灯远程控制程序，本设计建立在CC1110和TPS40211基础之上。-AN080-- LED Lighting with Remote Control using CC2510 and CC1110 This note describes a LED lighting design based on CC2510 and TPS40211. CC2510 is 2.4GHz System-on-Chip Low Power RF Transceiver wh
odeint
- Solving ordinary differential equations in C++development-This article introduces the C++ framework odeint for solving ordinary differential equations (ODEs), which is based on template meta-programming. I think this framework has some nice advantage
4.5_V_TO_52_V_INPUT_CURRENT_MODE_BOOST_CONTROLLER.
- 4.5伏到52伏输入电流模式升压控制器，是美国德州仪器公司的一个很好用的电流控制芯片-4.5-V TO 52-V INPUT CURRENT MODE BOOST CONTROLLER
28335_mppt
- 4路pwm，buck升压，错相抑制电流脉动-4 pwm, buck boost, current ripple-phase inhibition
C3D04060E
- 600-Volt Schottky Rectifier • Optimized for PFC Boost Diode Application • Zero Reverse Recovery Current • Zero Forward Recovery Voltage • High-Frequency Operation • Temperature-Independent Switching Behavi
1871
- 只电流模式升压芯片,需要极少外部元件的宽输入，电流模式、升压、反激和SEPIC控制器-Only current-mode boost chip requires minimal external components of wide input, current mode, boost, flyback and SEPIC Controller
1
- 提出了一种新型的单开关升-降压式(Buck-Boost)直流变换器的电路仿真平均模型。这种模型可通过输 入参数的选择实现对Buck-Boost电路的电压控制、峰值及平均电流控制,以及对DCM-CCM工作方式的统一。它 是一种实用的仿真模型,可方便地进行稳态和动态分析。在保证准确的基础上,大幅度提高了仿真的速度,通常比 用实际器件开关电路的仿真速度提高两到三个数量级。 -A novel average model for single switch Buck-Boost DC/DC
ADC_CC2
- 英飞凌单片机XE162的开发应用，能够使得boost电路的电压完成PID控制，并且有电压电流采样-Chip XE162development and application, can make boost circuit voltage PID control, and the voltage and current sampling
AN-1067
- In higher power applications to utilize the full line power and reduce line current harmonics PFC Pre-regulators are generally required. In these high power applications interleaving PFC stages can reduce inductor volume and reduce input and outp
boost_current
- boost电路matlab仿真 采用电流闭环-boost circuit the matlab simulation using current closed loop
new1
- boost电路matlab仿真，输入为带有波动的直流电压 要求占空比为0.5-boost current road
i_t_1int
- current in boost cover.
My_CS_mod3
- cs mod current in boost cover.
u_t_1int
- current in buck - boost cover.
final-res
- Grid-Connected Boost-Half-Bridge Photovoltaic Microinverter System Using Repetitive Current Control and Maximum Power Point Tracking
MPPT
- 太阳能光伏阵列在光照强度不均匀或者处于部分遮阴情形时，它的功率一电压输出特性曲线将出现多峰现象，这种情况下如果继续采用传统的最大功率跟踪法会造成光伏阵列输出功率的降低，从而导致光伏发电系统的效率的降低。 本文首先介绍了光伏并网发电的研究背景和意义，分析了国内外的现状和光伏并网发电关键问题的现状，接着对光伏电池的工作原理、等效模型和输出特性三方面进行了作了全面的分析 在此基础上，深入研究了热斑效应和部分遮阴条件下光伏电池不同的表现性能 然后，本文详细介绍了常用的最大功率跟踪方法的原理、优缺
buck_boost
- DC-DC升降压电路,主要实现升压和降压功能，采用PI电压电流双环控制-DC-DC buck-boost circuit, the main step-up and step-down function, using the PI voltage and current loop control
power_bank_CODE
- 移动电源程序，PWM软件恒流充电、升压、自动退载、过流、短路保护。限充。-Mobile power program, PWM constant current charging software, boost, automatic withdrawal overload, overcurrent, short circuit protection. Limit charge.